收藏本站
NCP5007
PIN FUNCTION DESCRIPTION
Pin
1
Symbol
FB
Type
ANALOG
INPUT
Description
This pin provides the output current range adjustment by means of a sense resistor connected
to the analog control or with a PWM control. The dimming function can be achieved by applying
a PWM voltage technique to this pin (see Figure 29). The current output tolerance depends
upon the accuracy of this resistor. Using a " 5% metal film resistor, or better, yields good output
current accuracy. Note: A built?in comparator switches OFF the DC?DC converter if the voltage
sensed across this pin and ground is higher than 700 mV typical.
2
GND
POWER
This pin is the system ground for the NCP5007 and carries both the power and the analog
signals. High quality ground must be provided to avoid spikes and/or uncontrolled operation.
Care must be observed to avoid high?density current flow in a limited PCB copper track so a
robust ground plane connection is recommended.
3
EN
DIGITAL
INPUT
This is an Active?High logic input which enables the boost converter. The built?in pulldown
resistor disables the device when the EN pin is left open. Note the logic switching level of this
input has been optimized to allow it to be driven from standard or 1.8 V CMOS logic levels.
The LED brightness can be controlled by applying a pulse width modulated signal to the enable
pin (see Figure 30).
4
V out
POWER
This pin is the power side of the external inductor and must be connected to the external
Schottky diode. It provides the output current to the load. Since the boost converter operates in
a current loop mode, the output voltage can range up to +22 V but shall not exceed this limit.
However, if the voltage on this pin is higher than the OVP threshold (Over Voltage Protection)
the device enters a shutdown mode. To restart the chip, one must either apply a low to high logic
signal to the EN pin, or switch off the V bat supply.
A capacitor must be used on V out to avoid false triggering of the OVP (Overvoltage Protect)
circuit. This capacitor filters the noise created by the fast switching transients. In order to limit
the inrush current and still have acceptable startup time the capacitor value should range
between 1.0 m F and 8.2 m F max. To achieve high efficiency this capacitor should be ceramic
(ESR t 100 m W ).
Care must be observed to avoid EMI through the PCB copper tracks connected to this pin.
5
V bat
POWER
The external voltage supply is connected to this pin. A high quality reservoir capacitor must be
connected across pin 5 and Ground to achieve the specified output voltage parameters. A
4.7 m F/6.3 V, low ESR capacitor must be connected as close as possible across pin 5 and
ground pin 2. The X5R or X7R ceramic MURATA types are recommended.
The return side of the external inductor shall be connected to this pin. Typical application will
use a 22 m H, size 1210, to handle the 10 to 100 mA output current range. When the desired
output current is above 20 mA, the inductor shall have an ESR v 1.5 W to achieve good
efficiency over the V bat range . The output current tolerance can be improved by using a larger
inductor value.
http://onsemi.com
3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCP5008DMR2 IC LED DRVR WHT BCKLT 10MICROSMD
NCP5010FCT1G IC LED DRVR WHT BCKLT 8-FLIPCHIP
NCP5021MUTXG IC WHITE LED DVR HV AMB 16-UQFN
NCP5050MTTXG IC LED DRIVR PHOTO FLASH 10-WDFN
NCP5111DR2G IC DRIVER HI/LOW SIDE HV 8-SOIC
NCP5304DR2G IC DRIVER HI/LOW SIDE HV 8-SOIC
NCP5355DG IC DRVR SYNC BUCK MOSF 12A 8SOIC
NCP5359ADR2G IC MOSFET GATE DVR DUAL 8-SOIC
相关代理商/技术参数
NCP5007SNT1G 功能描述:LED照明驱动器 White LED Backlight Boost RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5008 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators
NCP5008/D 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:White LED Driver
NCP5008_06 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Backlight LED Boost Driver
NCP5008DMR2 功能描述:LED照明驱动器 15V Output Max LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5008DMR2G 功能描述:LED照明驱动器 15V Output Max LED Backlight RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5009 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Backlight LED Boost Driver
NCP5009DMR2 功能描述:IC LED DRVR WHT BCKLT 10MICROSMD RoHS:否 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT